ac control (120vac) spf240a25 model numbers (24vac) spfe240a25 dc control (5vdc) spf240d25 spf380d25 spf480d25 (24vdc) spfe240d25 spfe380d25 spfe480d25 output specifications 1 operating voltage (47-63 hz) [vrms] 12-280 48-530 48-660 load current range [arms] forced air.06-25 3 convection air .06-10 transient overvoltage [vpk] 600 1200 1200 max. surge current, (16.6ms) [apk] 250 250 250 max. on-state voltage drop @ rated current [vpk] 1.6 1.6 1.6 maximum i 2 t for fusing, (8.3 msec.) [a 2 sec] 260 260 260 max. off-state leakage current @ rated voltage [marms] 0.1 0.1 0.1 min. off-state dv/dt @ max. rated voltage [v/sec] 2 500 500 500 max. turn-on time 4 1/2 cycle (dc control), 10.0 msec (ac control) max. turn-off time 1/2 cycle (dc control), 40.0 msec (ac control) power factor (min.) with max. load 0.5 0.5 0.5 input specifications 1 dc control ac control nominal voltage 5vdc 5vdc 24vdc 120vac 24vac spfe240d25 model numbers spf380d25 spfe380d25 spf240d25 spf480d25 spfe480d25 spf240a25 spfe240a25 control voltage range 3-15 vdc 4-15 vdc 15-32 vdc 90-140 vrms 18-36 vrms max. turn-on voltage 3.0 vdc 4.0 vdc 15.0 vdc 90.0 vrms 18.0 vrms min. turn-off voltage 1.0 vdc 1.0 vdc 1.0 vdc 10.0 vrms 2.0 vrms nominal input impedance 300 ohm 240 ohm 1500 ohm 14.1k ohm 2.1k ohm typical input current @ nominal voltage 15 madc 15 madc 15 madc 10 marms 10 marms general notes 1 all parameters at 25c unless otherwise specified. 2 off-state dv/dt test method per eia/narm standard rs-443, paragraph 13.11.1 3 heatsink temperature 85?c maximum. 4 turn-on time for random turn-on versions 0.1msec (dc control models). ? ultra high steady state current rating ? low leakage (off-state) ? scr output ? ac or dc control ? crydom's patented design series spf. rev. 111507 page 1 of 3 tm crydom?s powerfin tm series delivers the highest ratings of any single in-line pack- age (sip). the integral heat sink design can operate at 25 amps rms in forced air at 85?c case temp. with natural convec- tion in free air, it rates 10 amps rms at 25c ambient. built-in advantages include surface mount technology and scr output. manufactured in crydom's iso 9001 certified facility for optimum product performance and reliability. ? 2007 crydom inc., specifications subject to change without notice. series spf , powerfin up to 25amp ? 120/240/380/480 vac - ac output for recommended applications and more information contact: usa: sales support (877) 502-5500 tech support (877) 702-7700 fax (619) 710-8540 crydom inc., 2320 paseo de las americas, ste. 201, san diego, ca 92154 email: sales@crydom.com web site: http://www.crydom.com uk: +44 (0)1202 606030 ? fax +44 (0)1202 606035 crydom ssr ltd., arena business centre, holyrood close, poole, dorset bh17 7fj, email: intsales@crydom.com. germany: +49 (0)180 3000 506
0 10203040506070 80 ambient temperature (c) 0 2 4 6 8 10 load current (amps) 0 5 10 15 20 25 load current (amps) 0 20 40 60 80 100 120 140 heatsink temperature (c) general specifications dielectric strength 50/60hz input/output 4000 vrms insulation resistance (min.) @ 500 vdc 10 9 ohm max. capacitance input/output 8 pf ambient operating temperature range -30 to 80c ambient storage temperature range -30 to 125c mechanical specifications weight: (typical) .85 oz. (25g) encapsulation: thermally conductive epoxy all dimensions are in inches (millimeters) series spf. rev. 111507 page 2 of 3 fig.1 convection cooling fig.2 forced air cooling current derating curves available options r random turn-on (ac & dc control, 240v only) phase controllable (dc control, 240v only) example: spf240a25r, spfe240d25r ? 2007 crydom corp, specifications subject to change without notice. dc control pin 1: ac load pin 2: ac load pin 3: +dc control pin 4: -dc control ac control pin 1: ac load pin 2: ac load pin 3: ac control pin 4: ac control 1.70 0.06 dia. 4 places 4 3 2 1 1.60 0.035 1.35 0.10 0.90 0.02 0.30 0.06 0.72 0.02 0.05 0.025 1.10 0.02 0.70 0.02 0.040 0.0015 0.20 0.01 tm series spf , powerfin up to 25amp ? 120/240/380/480 vac - ac output approvals ul e116950 for recommended applications and more information contact: usa: sales support (877) 502-5500 tech support (877) 702-7700 fax (619) 710-8540 crydom inc., 2320 paseo de las americas, ste. 201, san diego, ca 92154 email: sales@crydom.com web site: http://www.crydom.com uk: +44 (0)1202 606030 ? fax +44 (0)1202 606035 crydom ssr ltd., arena business centre, holyrood close, poole, dorset bh17 7fj, email: intsales@crydom.com. germany: +49 (0)180 3000 506
hazard of electric shock, explosion, or arc flash. ? disconnect all power before installing or working with this equipment. ? verify all connections and replace all covers before turning on power. failure to follow these instructions will result in death or serious injury. riesgo de descarga electrica o explosion. ? desconectar todos los suministros de energia a este equipo antes de trabajar con este equipo. ? verificar todas las conexiones y colocar todas las tapas antes de energizer el equipo. el incumplimiento de estas instrucciones puede provocar la muerte o lesiones serias. risque de descharge electrique ou explosion ? eteindre toutes les sources d'nergie de cet appareil avant de travailler dessus de cet appareil ? vrifier tous connections, et remettre tous couverts en olace avant de mettre sous de non-suivi de ces instructions provoquera la mort ou des lsions srieuses srieuses. gefahr eines elektrische n schlages oder einer explosion. ? stellen sie jeglichen strom ab, der dieses ger?t versorgt, bevor sie an dem ger?t arbeiten durchfhren ? vor dem drehen auf energie alle anschlsse berprfen und alle abdeckungen ersetzen. unterlassung dieser anweisungen k?nnen zum tode oder zu schweren verletzungen fhren. rischio di scossa elettrica o dell?esplosi one. ? spenga tutta l'alimentazion e che fornisce questa apparecchiatu ra prima del lavorare a questa apparecchiatu ra ? verificare tutti i collegamenti e sostituire tutte le coperture prima della rotazione sull'alimentazi one l'omissione di seguire queste istruz ioni provocher la morte o di lesioni serie risco de descarga elttrica ou explos?o ? desconectar o equipamento de toda energia antes de instalar ou trabalhar com este equipamen to ? verificar todas as conex?es e recolocar todas as tampas antes de religar o equipamento o n?o cumprimento destas instru??es pode levar morte ou les?es srias. risque de dommage materiel et de surchauffe du boitier ? les panneaux latraux du produit peuvent tre chauds. laisser le produit refroidir avant de le toucher. ? respecter les consignes de montage, et notamment les couples de serrage. ? ne pas laisser pntrer de liquide ni de corps trangers l'intrieur du produit. risk of material damage and hot enclosure ? the product's side panels may be hot, allow time for product to cool before touching. ? follow proper mounting instructions including torque values . ? do not allow liquids or foreign objects to enter this product. le non-respect de cette directive peut entra?ner, des lsions corporelles graves ou des dommages matriels. failure to follow this instruction can result in serious injury, or equipment damage. la mancata osservanza di questa precauzione pu causare gravi rischi per l'incolumit personale o danni alle apparecchiature. si no se respetan estas precauciones pueden producirse graves lesiones, da?os materiales. die nichtbeachtung dieser anweisung kann k?rperverletzung oder materialsch?den zur folge haben. a n?o observancia destas precau??es pode provocar a morte, ferimentos graves ou danos materiais. gefahr von materialsch?den und geh?useerhitzung ? die seitenw?nde k?nnen hei? sein. lassen sie das produkt abkhlen, bevor sie es berhren. ? beachten sie die montageanweisungen, ? fhren sie keine flssigkeiten oder fremdk?rper in das produkt ein. rischio di danni materiali e d'involucro caldo ? i pannelli laterali dell'apparecchio possono scottare; lasciar quindi raffreddare il prodotto prima di toccarlo. ? seguire le istruzioni di montaggio corrette. ? non far entrare liquidi o oggetti estranei in questo apparecchio. riesgo de da?os materiales y de sobrecalentamiento de la unidad ? los paneles laterales del producto pueden estar calientes. esperar que el producto se enfre antes de tocarlo. ? respetar las instrucciones de montaje, y en particular los pares de apretado. ? no dejar que penetren lquidos o cuerpos extra?os en el producto. risco de dano material e de aquecimento ? os painis laterais do produto podem estar quentes; d tempo ao produto para arrefecer antes de lhe tocar. ? siga devidamente as instru??es de montagem. ? n?o permita a entrada de lquidos e de objectos estranhos no produto. danger / peligro / danger /gefahr / pericolo / perigo warning / avertissement / warnung /advertencia / avvertenza / aviso series spf. rev. 111507 page 3 of 3
ann ex ? e nvironm ental i nformati on: the environmental information disclosed in this annex including the eip pollution logo are in compliance with people?s republic of china electronic industry standard sj/t11364 ? 2006, marking for control of pollution caused by electronic information products. part toxic or hazardous substance and elements name lea d mercury cadmiu m he xav a len t polybrominated polybrominated (pb) (hg) (cd) chromium (cr (vi)) biphenyls (pbb) diphenyl ethers (pbde) se micondu ct or di e x o o o o o solder x o o o o o l - )? c : !8 l ? / ,x + $ c {
? "5 ? ,x )? c 0 " ? !? e
` ? + $ > ? ? ? sj/t11364 - 2006, + $ c {
? "5 {
? a? ?u " 2? b (= ? y !| y f? /? j? "2 k a?j ?$?6(8? ?$?`8?gn (pb) (hg) (cd) (cr (vi)) (pbb) (pbde) e'8?( x o o o o o &ty&? x o o o o o ? 2007 crydom inc., specificat ions subject to change without notice.
|
